Your Flexispot Konfigurator

Flexispot Standing Desk Evaluation …Flexispot Konfigurator…

Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a few features that I wasn’t necessarily a huge fan of:

The package that the desk was available in was heavy, so bringing it inside was a group effort, however this is just an effect of how sturdy the Flexispot is.
The hassle-free cable television tray was a bit complicated to install. In the end, you eventually slip it under screws, which wasn’t extremely clear from the guidelines.
You will require to buy an anti-fatigue mat to stay comfy, however this is an excellent concept for any standing desks, so I can’t fault Flexispot for that.

When it showed up and I saw how heavy it was, I was both thrilled (given that this suggested it was going to be sturdy) and also a little reluctant (since all of us know just how much of a challenge putting together furnishings can be).

The good news is, with the help of an educational YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only hang-up I have with assembly was the cable television tray, which I discovered wasn’t described well in the directions.

Once assembled, I enjoy the streamlined appearance of this desk. I’m positive any of the many varied surfaces that it comes in would look fantastic in any workplace, and the adjustable width makes it easy to fit it in even the tiniest of home offices.

The peaceful operation and height memory settings make it simple, efficient, and quiet to change in between sitting and standing as many times as you desire throughout the day.

Lastly, this desk is durable. It can hold up to 335 lbs even while in operation, so if you have a large home computer (or wish to rest on it for some reason) it has you covered. It will also equally disperse weight no matter how out of balance the weight you place on it is, it will not wiggle or wobble.

 

because video is quite kitted out as the desk we’re looking at today is quite basic I attempted to get as near to that as I might on uplifts website with similar setups the flexi area desk we’re looking at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift design is actually 5 inches longer but you can do a lot with 5 inches boom yes now for openness flexi spot did send this desk out for evaluation however as you must know by now doesn’t affect my review in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not shipping until completion of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can possibly get doing not have even any cable grommets for travel through the outdoors container

for the desktop was not damaged in any way which is absolutely bizarre due to the fact that I could shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted simply super rough guy if I had purchased this I ‘d have been on the phone with customer service instantly they did also handled to miss out on drilling the pilot holes where you can attach the control box to the desktop a lot of having to do that myself without accidentally drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was actually quite simple the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each component to support motorized function unusually definitely where any type of cable management materials whatsoever the frame on this unit is a single motor double stage design versus the double motor three-stage design that comes standard with the uplift desk this can be upgraded also to both the dual stage dual motor and a three-stage double motor which presses the cost of the desk up

an extra 70 bucks the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can range from simply under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than tall adequate even for me and I stay at 6 foot for this model does come standard with the control board that enables up-and-down movement plus 3 memory areas with an LED readout to tell you the desk height the single motor style utilizes this drive shaft assembly which has to be adjusted as the width of the desk is changed the motor operation itself while it might be slow is extremely peaceful as in barely audible this outside a price would be the one advantage I would provide this system over the uplift desk and I wish to take care here because this isn’t a hit piece this desk is 240 dollars cheaper than the equivalent uplift model over 35% cheaper even if you upgrade this flexi spot test to the double motor three-stage style it still comes in a hundred and seventy dollars cheaper than the uplift however cheaper doesn’t mean low-cost this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is strong even if max height I’ll absolutely give it that however the lateral stability of this desk the horizontal movement at this rate point it’s undesirable it’s rub salt in the wound here they include a little security baffle this little steel piece that installs to the frame and covers a part of this rotating driveshaft when

this desk sees any lateral motion at all the drive shaft hits the sound and this baffle is definitely shocking to top things off I decided to include rolling casters to this desk this was a $30 upgrade and two of those 4 casters showed up harmed also my plan for this desk at this point is to lose the desk top and came with all together and change it with a white laminate lemon table from Ikea and utilize it as an adjustable image table which you can’t do this frame will accommodate desktops as much as 63 inches large and 31 and a half inches deep so this will roll around the studio make it simpler to film items without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift first that is a financial investment in quality workplace furniture that will last you this at finest feels like a less expensive imitation of that it simply doesn’t feel quality and the distinction between this desk and my primary desk is night and day do do not hesitate to have a look at their site also which also feels eerily comparable to one of their competitors there’s a wealth of accessories you can get for the flexi spot desk approximately and including a foot massager and even a fixed exercise bike and I could spend another 10 minutes of our precious time covering various choices and devices I could however I believe I’m happier that they just sent out a basic desk due to the fact that as a standard desk I’m not a fan of the quality assurance at this rate point and I don’t believe slapping on a bunch of additionals is the relocation when the core item isn’t what it need to be they do provide a 30-day trial if you’re simply morbidly curious and they service warranty their desks for three years really desk is five years and uplift desk is seven years if you are Flexispot Konfigurator

in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in regards to gaming and efficiency but I would invest the extra money it’s gon na require to enter a higher end producer like uplift desk or really desk and I have not personally used extremely desk products so I can’t speak on it however their reputation is very good huge thanks to flexi area for sending this out for review regrettably I can not advise this system and for the record I’m a hundred percent sure they would have happily replaced the parts that I had a concern with viewing as how both the desktop and the casters got here harmed however from a customer perspective you ‘d most likely be truly delighted to get this in